Ultroner have as long as I remember, made mainstream stabilised wood products. The Ultroner Mini Stick is no exception. It is ultra small, wrapped in a Stabilised Wood sleeve to give you those sexy Stabilised Wood looks.
One thing I will say right now, if you are looking to get an Ultroner Mini Stick, this isn’t for the new vaper, you must know Ohm’s Law and a knowledge of Mechanical Mods.
There is no doubting Ultroner have certainly made a super tiny vape mod here but I personally think more thought could have gone into naming it!
Ultroner was founded in 2016. They mainly produce electronic vape products with the Stabilized Wood finish.
What Can We Expect From The Ultroner Mini Stick?
The Ultroner Mini Stick is just 48mm in length, is powered by 1X 18350 battery and is of course finished with a Stab Wood sleeve. It comes in 4 colours with either a SS or Black housing.
This device was sent to me for review by Vapeciga, thank you. As always, I will give you my own, honest opinion of this product after a lengthy testing period.
See The Ultroner Mini Stick In Action – Hands On Vode
In The Box
- Ultroner Mini Stick
- Lanyard
- Warranty Card
- Beauty Ring/Lanyard attachment
- Rubber block
Features
- Size: 24 x 48mm
- Battery: 1 × 18350 (not included)
- Mechanical mod with MOSFET switch
- Ultem Fire button
- Stabilised wood sleeve with Stainless Steel body
- Resistance range: 0.5ohm minimum
Design and Build Quality
Well, the design of Ultroner Mini Stick is basic but this is a mini Mechanical Mod after all.
By this, I mean you have a tube with two detachable ends. The top cap houses the MOSFET switch whilst the bottom cap has a screw down adjuster for your battery.
You have a stainless steel tube that houses your battery and a Stabilised Wood sleeve that goes over the stainless steel tube.
That been said, it all fits together very well and the build quality is very good as you would expect for something of this price point.
As far as I can tell after a lot of research, the MOSFET board at the top of the Mod is only to act as a switch and will not give you very much protection at all.
Bear this in mind when you use your RDA or RTA with this. Ultroner recommend all builds to be 0.5ohm or above. I would highly recommend you take heed of this!
On the bottom of the device, you have two large battery venting ports as well as the means to tighten or loosen the connection with the battery to stop any rattle.
The 510 connector is on the top of the device but be careful with the top of the MOSFET board.
There is a small piece of metal, that, over time will be pushed down with differing sized 510 pins. I can only presume the small rubber block is to put under this to prevent this from happening.
The MOSFET board is very fragile. If you have to take it out for any reason at all, be very careful. Also, if you do remove it, keep an eye on the Ultem fire button as this will just fall out.
The Fire button is nicely placed on the Mod though it is only comfortable for me firing it with my thumb. If you were to use your finger to fire the device, it becomes very awkward.
Batteries and Placement
On the bottom cap to the Ultroner Mini Stick, it’s clearly marked negative. Simply place your 18350 battery into the main body positive up and screw on the bottom cap then adjust accordingly.
How Does The Ultroner Mini Stick Perform?
I do know that you can get the Ultroner Mini Stick as a kit with an RDA thrown in. I do however feel that this kit is best used with an MTL RDA or RTA because it isn’t recommended to go below 0.5ohms when you put a build in your device.
I have used the Ultroner Mini Stick primarily with the Kayfun Lite 2019 RTA and it has performed very well. I have also used it with the Digiflavor Drop Solo, whilst the vape from this was ok, it just wasn’t for me.
Battery Life
You aren’t going to get massive amounts of battery life from any 18350 battery no matter what you do. However, using this as I did, as a carry round and vaping it for a nicotine hit with 20mg Nic Salts, it can last all day.
If you are using it as your main device, then you will get two to three hours at best.
Pros
- Superb small form factor
- Great Looks
- Stabwood Sexiness
- Easy to use
- Well Built
Cons
- MOSFET board is only a switch style
- No protection from MOSFET
- No instruction manual
- No warnings
- No information at all!
Final Review Verdict
Ok, this is a lovely, small mechanical device. Super sexy Stabwood if that’s your thing. It performs very well for its small form factor but it certainly isn’t going to be anyone’s daily driver, though I don’t think that’s Ultroners intention at all.
If you’re looking for something that’s a little different, something away from mainstream vaping devices then I think this would be a very good buy for you.
You aren’t going to be blowing huge arse clouds from this and don’t think it’s going to be a hard hitting Mechanical Mod, it’s none of those.
This is, though, an ideal device for some MTL vaping and you can show off some of that Stabwood sexiness. Did I mention Stabwood?
