The Steelvape Tailspin kit is a hybrid mod kit which also includes a hybrid tank as well!
tailspin plain sleevesThe Tailspin mod is a single 18650 mod of 25mm in diameter.

There are various different finishes and materials for this kit.

steelvape tailspin kit marketing shotsThe actual tube section is made from Brass.

Then you install a sleeve over the brass – the sleeves are either resin or aluminium and come in different colours and finishes.

tailspin componentsThe mod is a mechanical mod so you will need to make sure you know your battery safety and ohms law. The minimum coil resistance you can use on this is 0.05ohm – but again this is dependent on the battery you are using as the battery is not included.

The fire switch is hidden below the base of the mod. The switch has a copper contact and is spring operated.

The top of the mod has a hybrid 510 connector.

The Tailspin tank is a RDA and RDTA hybrid. Using the supplied tank this is a RDTA or you can installed the included RDA base.

tailspin tankA resin drip tip and a POM drip tip are included in the kit and they turn to control the air intake to the tank.

tailspin top capThe sleeve comes in aluminium Black or Red or resin which is a black pattern.

The mod and tank have the same colour accents and they are available in Stainless steel, Gold, Black, Antique brass, Brushed silver and Antique copper.

Kit Includes

  • Steelvape Tailspin Mod
  • Steelvape Tailspin RDTA
  • RDA bottom
  • Resin drip tip
  • POM drip tip
  • Tank cap
  • Manual
  • Accessories

steelvape tailspin kit contents

 Steelvape Tailspin Mod Specs

  • Material: Brass
  • Diameter: 25mm
  • Height: 84mm
  • Powered by 1 x 18650 battery (not included)
  • Replacement aluminium and resin sleeve
  • Minimum atomizer resistance 0.05ohm support
  • Hybrid style mod, hidden button
  • Spring button, plane contact, copper pin

tailspin specs

Steelvape Tailspin RDTA Specs

  • Stainless steel construction
  • Diameter: 25mm
  • Height: 38mm (RDA), 52mm (RTA)
  • Capacity: 4ml
  • Switch between RTA and RDA
  • Dual post design, two post hole of each post, easy to set up DIY coil
  • 6mm deep juice well
  • Side filling port
  • Silver plated 510 connection
  • AFC 810 resin and POM drip tip included

tailspin tank specsThere is no doubting this is a seriously good looking and classy kit!

The price however is way lower than you would expect for the whole kit – I am really surprised!

Plus if this starts looking a bit beaten or tatty you can simply swap the sleeve and make it look like new again!

Has this got your tail in a spin (groan…) ? Let me know your thoughts in the comments below!

Shell Ecigclick Photo
Michelle Jones

I am an engineer and Technical Author by trade. My journey in vaping began around 2016, in the days of Tornado tanks, Ego batteries and Variable Voltage. It took me a few years to fully quit smoking but I finally stopped in June 2019 and that is all thanks to vaping! 20mg Nicotine Salts are my hero! Oh and I am partial to a nice pod mod and Bubblegum e-liquid! I have reported on the latest news on Ecigclick since 2017 and love being part of this great team! My passion for Tobacco Harm Reduction has also led me to becoming a Trustee for the NNA (New Nicotine Alliance) aiding in Advocacy

I am an engineer and Technical Author by trade. My journey in vaping began around 2016, in the days of Tornado tanks, Ego batteries and Variable Voltage. It took me a few years to fully quit smoking but I finally stopped in June 2019 and that is all thanks to vaping! 20mg Nicotine Salts are my hero! Oh and I am partial to a nice pod mod and Bubblegum e-liquid! I have reported on the latest news on Ecigclick since 2017 and love being part of this great team! My passion for Tobacco Harm Reduction has also led me to becoming a Trustee for the NNA (New Nicotine Alliance) aiding in Advocacy

LEAVE A REPLY

Please enter your comment!
Please enter your name here